content top

Adjusting Your Water Heater Thermostat

One of the critical components of your home or business water heating system is the thermostat. Basically, a thermostat is a motorized device which regulates the flow of electrical voltage to the heating elements of the water heater system. In effect, not only does the thermostat provide comfort, but also guarantees safety inside the home. When set extremely high, the resulting hot water may cause burns and injuries. When set extremely low, bacteria may thrive in the resulting cold water. In this regard, homeowners need to be familiar with accessing the water heater thermostat in order to keep their hot water at the optimal temperature for their specific needs. Finding the water heater thermostat The two most common types of water heaters are gas and electric water heating systems. The location of the thermostat in both the electric and gas water heaters differs. Electric water heaters The electric water heating system features two thermostats, namely the upper and lower thermostat, each hidden at the back of the metal access casings on the tanks. Prior to embarking on anything else, switch off the electrical current to the water heating system. Unbolt the two holding screws in the initial thermostat cover. Take out the door, and eliminate any insulation beneath it. Finally, you will see the thermostat featuring a set screw for changing the temperature setting. The thermal controls may be tagged with specific temperatures, or may simply specify warm and hot. Upon setting your desired temperature setting, reinstate the insulation as well as the access casing. Follow similar steps for accessing the second thermostat. Note that the upper and lower thermostats should be set at corresponding temperature settings, to which the one set at a higher temperature may fail to power on while the other one set at a lower temperature may break down from constant use. Switch on the power again once you’re done. Gas water heaters In contrast to electric water heaters, the thermostat in gas water heaters is easily reachable, on the obverse of the tank adjacent to the base, despite the fact that on some versions it may be hidden underneath the access cover. On the majority of gas water heating systems, the thermostat is coupled with the main gas valve as well as the pilot valve in a single unit to form a combination control mechanism. Typically, the gas controls are plainly labeled. Adjust the knob to your preferred temperature setting. Reinstate the access casing if there’s one. Regulating the temperature setting of your water heater demands knowledge of where and how to access the system’s thermostat. If you find you need additional help with your water heater thermostat, contact...

Read More

Types Of Electrical Services And Factors To Consider When Using Them

Electrical services involve all activities and services rendered by trained and certified technicians called electricians that touch on electrical supply systems, electrical appliances and related equipment. Apart from installation work, these services are very important in ensuring that electrical systems and appliances function properly. Faulty electrical systems pose a great danger to users in the vicinity as well as any electrical appliances connected. Therefore, trained and certified technicians or engineers should handle all electrical services involving repair, installation or maintenance work. Electrical services fall under the following general categories: Installation work – When new residential, industrial or commercial buildings come up, they need connections to the electrical grid. Such installations are part of the electrical services that electricians and electrical engineers handle. In addition to the electrical supply lines, these technicians install power meters, control switches and fuses as well as any other relevant electrical access and utility components that depend on electric power to function. Maintenance and diagnostics – Electrical systems are prone to faults and problems; therefore, electrical diagnostics and maintenance work are part of the electrical services that utility companies or private electricians handle. These duties involve physical checks on the supply lines, power meters, lighting, access and control systems using special diagnostics tools such as digital power meters. Repair work – When electrical systems malfunction due to systematic faults, lightning strikes or human error, repairs have to be done to reduce the offline period. When electrical power goes off, security lighting, commercial activities, health procedures, and activities in the home cease. Lack of electric power affects commercial, industrial and home activities, influences public security and jeopardizes millions of lives in hospitals. During installation, maintenance and repair of electrical systems in the home, skilled electricians should handle these risky jobs in order to ensure proper installation and functioning. Additionally, using these skilled technicians reduces the chances of property damage, injury or electrocution. Factors to consider when choosing electrical services providers include: Reliability – Based on the risks associated with faulty electrical systems, hiring reliable providers of electrical services for installation, maintenance and repair work is crucial. Companies and contractors with a good service record and skilled electricians should be the priority. Experience – Hiring electricians with the right amount of experience in all aspects of electrical services could ensure that the services one gets are satisfactory. High quality electrical services in the home improve safety while reducing costs associated with repairs and replacements. Certification and other qualifications – In order to receive the best electrical services, the providers should constitute highly qualified and certified electricians in order to avoid insurance and quality...

Read More

Grill Element Replacement For An Electric Oven

You will know if the grill element is not working properly in your electric oven; the element will either not come on at all or you will notice uneven patches or bright spots on some areas of the element. Although some grill elements can be changed quickly and easily from the front of the oven, many can only be changed by accessing the rear of the oven. This article looks at the process of changing the grill element in ovens that have to be accessed from the rear. Remove The Oven Door Begin by ensuring that the power to the oven is off. If you are unsure of where the switch is to do this, consider turning the main power supply off for a few minutes while you carry out this task. Open the oven door and look for the latches or hinges supporting the door on either side. These latches can be moved upwards to allow the door to come off.  Lift The Oven Out Grip the oven at the top, and lift it up and out. It will probably be lighter than you imagine. Continue to carefully lift the oven out and place it on the floor directly in front of the oven opening. Remove The Back Panel Use a screwdriver to remove the thin metal panel that covers the rear of the oven. There are usually two or four screws holding the panel in place. In some cases, you will need to remove the top panel as well so that you can access the rear panel. Move The Insulation And Take A Picture Of The Wiring Partially pull back the insulation covering the rear part of the oven. When the insulation has been moved, you will see the two prongs sticking out of the oven. You will also notice two small wires that are connected to each prong of the element. These are easy to remove; they are connected to small metal heads that can be slipped off. As a precaution, take a digital photograph of the prong part, so that you know where each wire goes after you have replaced the element. Use Pliers And A Screwdriver Use a pair of pliers to slip the wires and their heads off.  Then unscrew the screw that is situated on either side of the element. Once these are off, you can go to the front of the oven and slip the element out. Replace And Reverse Pop the new element into place and screw back the two screws next to the element, at the rear of the oven. Then simply reverse the work you did to access the element. Turn the power back on...

Read More

Lighting Tips for Interior Residential Spaces

The lighting in your home will determine the ambience, mood and even the functionality of the interior spaces. It is important to make the right choices when installing fixtures to avoid inappropriate brightness, dimness or general unsuitability. In simple terms, every section of a residential building requires varying lighting to fulfil different needs. Here is a short guide to help you improve the lighting in each room. Kitchen The kitchen is a busy environment with high human traffic; therefore, you should install bright lighting fixtures. Choose overhead bulbs and lamps for ambience and task lighting. You can set up recessed light for a contemporary sleek look in the room. These are designed to fit into the walls or ceiling so they will not affect the interior architecture significantly. If you prefer a less modern look, consider installing pendant lights. They hang from the ceiling by a stem cable which supports the light; this choice will give the kitchen a more traditional appearance. In addition, you should plan for under-the-counter lighting to prevent bumping of toes in the darkness. You can even engage an electrician to connect these with motion sensors. Bedroom The bedroom needs to be cosy, warm and welcoming; therefore, bright lights should never be in the space. They will not create a comfortable environment for rest and relaxation. Basically, the chosen lamps should be for ambience as opposed to task lighting. Install low wattage bulbs under lampshades and place them on the nightstands for soft and soothing lighting. If you like reading in bed, you can add another larger and brighter fixture, but this should be used sparingly. Bathroom The bathroom can be a hazardous place, so it is critical to ensure that there is sufficient lighting. If you have a small bathroom, overhead lighting over the mirror or in the ceiling is often adequate. The light should be bright to ensure proper visibility. On the other hand, it is vital to note that this lighting is very uncomfortable in the morning. Consider installing a dimmer to regulate the lights according to the immediate requirements. If you have created separate sections for the sink area and the bath or shower, you will need separate lighting. The sink area can utilise recessed overhead lighting, and you can install regular lambs or heat lamps in the bath or shower. The lighting plan for other areas should be simple. The dining room should be bright with central fixtures, while hallways should have adequate lighting with accessible switches at both ends. As you work to update your lighting, work with an experienced electrician you can safely complete any installations that may be...

Read More

Categorization Of Electricians And Factors To Consider When Choosing One

An electrician is a technician whose job entails fitting and repairing electrical circuits, components, and wiring in people’s homes, commercial property, and industrial installations. Apart from fitting and repair work, electricians install and maintain electrical equipment, and electrical instruments. The title of ‘electrician’ is a generally used to refer to the personnel commonly called upon to repair faulty electrical equipment, but it has a wider meaning. Electricians fall into many categories based on the type of work they do and their level of training. Categorization of electricians Installation electricians – These electricians install electrical systems and equipment in all types of buildings. Installation electricians deal with power systems, security systems, as well as fire and lightning electrical surge and spike protection systems. Electro-technical panel technicians – These electricians focus on the installation of control panels that measure and monitor the electricity consumption of all power users in the building. Their jobs usually correspond with the construction or restoration of the building on which the control panel works. Maintenance electricians – This category of electricians check that existing electrical systems and components are in good working order and operating in a safe manner. If need be, they have the skills and equipment necessary to intervene and make sure the systems and components work properly. Machine repair and rewind technicians – These electricians repair specialised electrical components that incorporate extensive cabling and wiring. Such electrical components include transformers, generators, and electric motors. Highway systems technicians -These electricians focus on electrical systems that guide and control motor vehicles and pedestrians on the highway. Their area of expertise revolves around traffic lights, highway lighting systems, electrical signage, and electrical pedestrian control equipment. When electrical systems and components fail, electricians and other trained personnel are called to repair them. However, choosing an electrician is a sensitive affair based on the risks associated with shoddy electrical repair jobs. Some of the factors to consider when choosing an electrician include: Recommendations – An electrician’s referrals and recommendations based on their history and quality of work is the best vetting tool in choosing one. Based on the technician’s referrals, their ability to provide excellent services can be determined. Experience – The second factor that influences the choice of an electrician is their experience. A highly experienced electrician is far better than one with lesser experience since more experience means a better job. Professionalism – Electricians called upon to offer repair or maintenance services must act in a professional manner. Electricians who act professionally provide high quality service since they put critical factors such as safety and system efficiency into consideration. For more information on electricians, go to a site...

Read More
Page 1 of 3123
content top
Menu